The most detailed introduction to connector selection skills
The expert of garden faucet hose fittings - Yuhuan Golden-Leaf Valve Manufacturing Co., Ltd. introduces you in detail the purchasing skills of garden faucet hose fittings.
Our Aluminum 4-Way Hose Connector products have been recognized by our customers with advanced production technology and excellent quality!
Nowadays, faucets are very common in our lives. Because of the faucets, it is very convenient for us to use water. In this way, we will not have to fetch water by ourselves as before, but directly turn on the faucet and clear water will come out. The faucet hose joint is a part of the faucet, and its quality affects the daily use of the faucet. So how do we choose in our life? How should the faucet hose joints be connected? In response to these problems, let's follow the editor to understand.
Faucet Hose Fitting Connection
Tools/Ingredients Buy a new sink drain wrench Triangle valve Raw material belt water faucet hose Method / Materials prepared for step 11 are as follows: Buy a new sink drain pipe, wrench, triangle valve, raw material belt, water pipe faucet hose . 2 If the triangular valve at home is rusted, first replace the triangular valve. Use a wrench to unscrew the old valve. The new valve is preferably made of copper, which is more durable. It is necessary to wrap a certain number of raw material tapes around the thread.
Then screw on the new copper triangle valve, there are 2 in total, one is the triangle valve for the hot water pipe and the other is the triangle valve for the cold water pipe. 3 Now start to connect the faucet hose to the faucet correctly. The faucet in my house is not broken, so I just use the old one. The sequential steps should be: 1. First put the casing of the faucet directly on the 2 hoses; 2. Then the hose passes through the jack of the faucet from below, 3. Then insert the copper connector of the hose into the faucet, and 2. All of them must be tightened, and you must be careful when tightening, do not use brute force, but use skillful force. But don't break as shown in the picture below. 4 After these steps are completed, the last two steps are left, one is to fix the faucet. One is to connect the hot and cold water pipes of the triangle valve below respectively.
The inside of the hose is rubber, the outside is stainless steel wire or aluminum wire, and the copper joint is used. Consumers can feel the quality of the hose from some appearances, such as stroking it by hand to feel whether the wires of the hose are neat, whether there is a rough feeling, and the grid arrangement is not disorderly; if the joint is black or black , indicating that the chrome plating process is not well done; the number of connecting threads should not be less than 3 teeth (too short, it is easy to seal poorly and cause water leakage, and even cause the nut joint to break), and the surface should not have broken teeth, dents and other defects; Some hoses use poor rubber and even smell. However, the current hoses are sold together with the faucet products, and the hoses of good faucet manufacturers are divided into hot water pipes and cold water pipes, which are marked with red and blue respectively. It is recommended to buy products with separate hot and cold water.
Also pay attention to the length of the hose. The length of the hose is divided into 200mm, 300mm and 500mm. If the hose is too long, the worker will bend it during installation; if the hose is too short, the worker will tighten a few buttons less when installing, resulting in fewer threads for the nut connection. Both of these conditions can lead to burst pipes in the long run. Therefore, it is recommended that consumers should measure the distance from the faucet to the angle valve before purchasing, and then choose the appropriate length of hose according to their needs.
The above is the connection method and selection method of faucet hose joints that have been simply sorted out and summarized by the editor. I believe that through the above content, everyone has a further understanding of faucet hose joints. Because the faucet is a very important part of our life, when we use the faucet hose joint, we should pay attention to his choice and try to choose the good quality, so as to reduce its maintenance times and make us feel comfortable.
